Showing posts with label plumbing repair. Show all posts
Showing posts with label plumbing repair. Show all posts

Thursday, August 29, 2013

Things that shouldn't go into your plumbing system

Avoid plumbing problems! Some common items that will stop up a toilet include: toys, hair, paper towels, birth control items, and feminine personal products. Do not flush these items down your toilet - unless the instructions say otherwise! These can stop up your toilet - to the point that nothing else will work - except calling a plumber!

To avoid clogs, pay attention to what you flush. Sanitary napkins, thick toilet paper and baby wipes should never be flushed. These items can expand and cause a clog, or get caught on a pipe. Instead, dispose of them in a sanitary way that does not involve flushing them down the toilet.

Certain things shouldn't go into your plumbing system. By knowing what you can and cannot flush or throw into the garbage disposal and sink, you can save yourself from a costly repair or disaster. A plumber can usually get your plumbing back into working condition, but can be avoided if you know how to dispose of items correctly.

To avoid sediment buildup, drain gallons of water from your water heater to flush any corrosion. This will help your heater to run more efficiently therefore saving you regular energy costs. Make sure to read your heater's instructions before attempting this, and do this periodically to make sure that your heater is running as well as it can.

Trash should go in the trash basket, not the toilet. Use the toilet for what it is designed for, and it won't give you a lot of problems. Never flush paper towels, tissue, diapers, or tampons. These things do not break up correctly and can clog your pipes. Additionally, use the minimum amount of toilet paper required to clean up after you are done.

It should not be necessary to call out a professional for every repair job. If you take your time and apply sensible advice, such as what you read here, you can successfully repair many of the common faults that develop. It may take a longer the first few times, but after a few successes you will pick up speed.

Monday, June 6, 2011

DIY Plumbing Repair - How To Fix A Leaking Faucet

Plumbing is something every home owner must deal with sooner or later, whether you are working on a remodeling project, or you need to fix any plumbing problems.

One of the most common plumbing problems is a leaking faucet. Here is how to fix it:
  1. The first thing you need to do is turn off the water supply to the sink, most of the time the valve is located right underneath, if not you need to follow the plumbing line to the nearest shut off valve. If the valve resists being turned, put a drop or two of oil right where the stem disappears into the large nut. Then use a wrench to loosen the nut one complete turn, and tighten it back up by hand. Wait for a couple of minutes and then you should be able to turn the valve off.
  2. The second thing to do is remove the stem from the top of the fixture, then there will be nut that needs to be turned counterclockwise to be taken off. Grasp the handle and turn it counterclockwise, as if you were turning on the water. The whole thing will lift out in your hand. If you have a ball-type fixture, there will be a setscrew on the lower surface of the handle itself, remove the screw. There will be a plastic ring or cap just unscrew and remove then pull out the ball assembly.
  3. Your almost finished with the repair. Now replace the washer, which should still be attached the ball assembly you just pulled out There is a screw holding it on, so remove that and replace it with the new washer, tighten the screw back on, be sure not to go to tight where the washer starts to become damaged. 
  4. Reinsert the stem assembly, and twist it firmly clockwise (don’t over tighten it). Tighten the large nut back into place. 
  5. Turn the water valve back on and that’s it! If it still leaks it may mean you have to replace the valve seat or replace the entire fixture. You will need to purchase a repair kit that you can find at your local plumbing supply or hardware store.
Use the following steps to replace the ball type fixture:
  1. Using the end of the screwdriver, lift out the rubber seats and springs. 
  2. Replace them with the new ones in the kit. Tug the spout off the base by turning it from side to side and lifting up. Then use the screwdriver to leverage the old O-rings off the base. If they need to be cut off, make sure that you clean off any remaining pieces. 
  3. Roll the new O-rings over the base to replace them. 
  4. Re-seat the faucet by turning it from side to side while pushing down. 
  5. Place the ball assembly back in there, and screw the rounded, knurled cap back on. 
  6. Before retightening the adjusting ring with the special tool, turn the water back on. Then tighten the ring until no water leaks, but don’t over tighten it. 
  7. Replace the handle, and tighten the setscrew. 
You should now be all set! It’s a good idea before starting this job to go to your local plumbing supply with the make of your faucet just to make sure that all the necessary parts are available.